The writer is very fast, professional and responded to the review request fast also. Thank you.
Book/movie review
22/08/2022
1. What is the reading on the following Vernier? What is its resolution?
2. What is the reading on the following micrometer? What is its resolution?
3. A Vernier caliper subdivides the smallest division on the main scale into 100 equal parts. If each subdivision on the Vernier plate equals 0.001 in, what is the length of the smallest subdivision on the main scale?
a) 100*0.001 mm b) 100 mm c) 0.1 mm d) a and c e) None of the above
4. A micrometer subdivides the smallest division on the main scale into 50 equal parts. If each subdivision on the thimble equals 0.001 in, what is the length of the smallest subdivision on the main scale?
a) 100*0.001 mm b) 0.001 in c) 50 equal parts d) None of the above
5. (SI units) A GO/NO-GO plug gage will be designed to inspect a 50.00 ± 0.20 mm diameter hole. A wear allowance of 3% of the total tolerance band is applied to the GO side of the gage. Determine (a) the nominal sizes of (a) the GO gage and (b) the NO-GO gage.
6. (SI units) A GO/NO-GO ring gage is needed to inspect the diameter of a shaft that is 50.00 ± 0.20 mm. A wear allowance of 3% of the entire tolerance band is applied to the GO side. Determine (a) the nominal sizes of (a) the GO gage and (b) the NO-GO gage.
7. (USCS units) A sine bar is used to determine the angle of a part feature. The length of the sine bar = 8.000 in. The rolls have a diameter of 1.000 in. All inspection is performed on a surface plate. In order for the sine bar to match the angle of the part, the following gage blocks must be stacked: 2.0000, 0.5000, 0.2500, and 0.0050. Determine the angle of the part feature.
8. (SI units) A 150.00 mm sine bar is used to inspect a part angle that has a dimension of 35.0° ± 1.0°. The sine bar rolls have a diameter = 25.0 mm. A set of gage blocks is available that can form any height from 10.0000 mm to 199.995 mm in increments of 0.005 mm. All inspection is performed on a surface plate. Determine (a) the height of the gage block stack to inspect the minimum angle, (b) the height of the gage block stack to inspect the maximum angle, and (c) the smallest increment of angle that can be set up at the nominal angle size.
9. (SI units) A 125.00 mm sine bar is to be used to inspect the inclination of one of the faces in a part. While the tolerance on the part inclination is +/-0.002 degrees, its nominal value can be anything from 5 to 85 degrees. If the smallest gauge block available is 0.01 mm thick, will this sine bar be of sufficient angular resolution to determine if all possible nominal part inclinations are within tolerance? Hint: Evaluate the resolution for inclination angles from 5 to 85 degrees and plot the resolution as a function of this angle. The plot will give you a visual aid to help you answer the question.
10. Convert 0.025 in into mm.
11. Convert 25 mm into in.
12. Convert 10.25 degrees into radians; and p, p/2 and p/3 radians into degrees.
13. Convert 30.12345 degrees into degrees, minutes and seconds.
14. How many degrees are equivalent to one second of arc?
15. Assume that the surface of a part has a profile given by y = 1.5×10^-6 in sin(2x/in). Both x and y are in inches. Answer the following questions:
a. What is the distance between peaks?
b. What is the value of Ra AA over 1 inch length?
c. What is the value of Ra RMS over 1 inch length?
d. What process may have produced such surface? Use a chart from the internet or elsewhere to support your answer.
16. What is the lay in the following surface symbols? Sketch the surfaces. Investigate what machining operations may produce such surface patterns.
17. Convert 1 μm into thousandths of an inch.
18. Convert one ten thousandth of an inch into μm.
19. For each of the following process pairs, circle the one that produces a smaller surface roughness. If the processes are about equal, circle both.
a) Sand Casting vs. Polishing
b) EDM vs. Turning
c) Rolling vs. Grinding
20. The surface roughness is generally smaller:
a) Across the lay
b) Along the lay
c) None of the above
d) Don’t know, will take the penalty!
The writer is very fast, professional and responded to the review request fast also. Thank you.
Delivering a high-quality product at a reasonable price is not enough anymore.
That’s why we have developed 5 beneficial guarantees that will make your experience with our service enjoyable, easy, and safe.
You have to be 100% sure of the quality of your product to give a money-back guarantee. This describes us perfectly. Make sure that this guarantee is totally transparent.
Read moreEach paper is composed from scratch, according to your instructions. It is then checked by our plagiarism-detection software. There is no gap where plagiarism could squeeze in.
Read moreThanks to our free revisions, there is no way for you to be unsatisfied. We will work on your paper until you are completely happy with the result.
Read moreYour email is safe, as we store it according to international data protection rules. Your bank details are secure, as we use only reliable payment systems.
Read moreBy sending us your money, you buy the service we provide. Check out our terms and conditions if you prefer business talks to be laid out in official language.
Read more